For clocks with hanging weights, check the weights occasionally to ensure that they are still tightly assembled.ĥ. Never spray the cleaner directly on the clock.Ĭhime Selection Lever – Safe and Unsafe Times, Figure 8Ĥ. When cleaning glass, use a non-ammonia glass cleaner. Use a non-silicone liquid or paste wax.ģ. Wax and polish your clock cabinet as frequently as you do your other furniture. Listed below are steps you can take to maintain the exceptional quality of your Howard Miller clock.Ģ. Your clock requires little care and maintenance. See figure 8 for when it is safe to move the chime selection lever without damaging the movement. Never change the selection while the clock is chiming or positioned near the release points. If your clock has a triple chime movement, the chime lever identifies the melody choices. If the dial states “WESTM-SILENT” (Westminster-Silent) or “STRIKE-SILENT”, your clock has only the Westminster chime. Some models play only the Westminster chime, while others give you a selection of three melodies.Īdjusting Speed on Pendulum Clocks – Figure 7 Selecting the chime melody is accomplished by moving a lever on or next to the clock dial.
To speed the clock up, move the lever up towards the “+” (plus). To slow the clock, move the lever down towards the “-” (minus). (24 hours).Ĭhanging the speed of time keeping is accomplished by moving the time adjustment lever. Turn the adjustment nut one complete revolution for each half minute fast or slow per day. To speed the clock up, move the pendulum disk up by turning the adjustment nut to the right. To slow the clock down, move the pendulum disk down by turning the adjustment nut to the left. The pendulum disk is moved up or down by turning the adjustment nut. Re-set the minute hand to exact, correct time.Ĭhanging the speed of time keeping is accomplished by moving the pendulum disk up or down. Adjust as detailed under “Clocks with Pendulum”or “Clocks without Pendulum”.ĥ. Is your clock fast or slow?Īdjusting Mechanical Clocks with and without Pendulums – Figure 6ģ. Compare time shown on your clock with correct time. Re-set the minute hand to the exact, correct time.ĭay Two, Three, Four, Five, Six (If Necessary)Ģ. Select a time of day that will allow you to check your clock at the same time for at least six days.Ĥ. DO NOT lift the weights by hand while cranking. For clocks with hanging weights, raise the weights using the crank. Turn the key clockwise until the spring becomes tight and will not turn further. Depending upon the model of your clock, there can be 1, 2, or 3 winding key holes. Insert the winding key into the holes located in the dial face.
Howard miller clocks manual#
Attach your sales receipt to this manual for future reference.
For easy reference in the future, take a moment to record these numbers in the space provided on page 5 of these instructions. Refer to this label when contacting your dealer or Howard Miller. The product information label is located either on the back or bottom of the clock.
Howard miller clocks serial number#
The clock model number and serial number are essential for obtaining parts or service. The product information label identifies the clock model number and serial number. Place the pendulum hook over the pin or through the slot on the end of the pendulum guide, and lower the pendulum until it is hanging securely on the pendulum guide. While holding the pendulum guide with one hand, slip the pendulum through the front door with your other hand. To hang the pendulum, locate the pendulum guide through the front door or back access panel. Carefully remove this film before hanging the pendulum. Some pendulums have a colored protective plastic film covering the pendulum disk. NOTE: To perform the following steps, Howard Miller suggests wearing cotton gloves or using a soft cloth when handling parts. Open the front door and remove the white plastic insert holding the minute hand at the 3:00 location (this insert is not used on all models).įollow the remaining instructions as they apply to your clock.įollow these instructions for hanging pendulum. (See figure 1 & 2)įor clocks with a pendulum, cut the rubber band or remove the metal spring clip from the back side of the movement by first pulling one end free. When possible, pull in the direction shown to remove. Remove foam, Styrofoam, and cardboard from around the movement and chimes. Mechanical Movement Mechanism Parts – Figure 2ĭO NOT PULL ON THE RUBBER BANDS TO BREAK.
0 kommentar(er)
